在升降機使用的有關規定中表明，一般在8米以上的升降作業已然是屬于中高空了，這個高度以上設備本身由于自身的重量開始出現不同幅度的晃動，晃動的幅度取決于載重物體的重量，以及升空的高度，升降機在高空作業的強度等因素。液壓升降機和液壓升降臺的晃動幅度與他的高度是正比的,高度越大晃動越大,在工作20米使用時一定要使用安全纜繩. 液壓升降機小幅度的晃動是正常的,在我們可以采取措施時,為了確保安全這是我們需要掌握的技巧.所以在不同的狀況中一定要學會采取適當的方法,盡量減小液壓升降機的晃動.
Used in the relevant provisions of the lift indicated generally at 8 meters above the lifting operation already belongs to the altitude, and the height above the device itself due to its own weight began to appear different magnitude shaking, shaking amplitude depends on the weight of the load of the object, and launch height, strength in aerial lifts and other factors. Hydraulic lifts and hydraulic lifts shaking amplitude is proportional to his height, the greater the height of the larger rock, 20 meters at work use safety rope must use hydraulic lifts a slight shaking is normal, we can take when measures to ensure the safety of this technique is that we need to know, so in different situations must learn to adopt appropriate methods to minimize hydraulic lifts shaking.

2、升降機作為一種剪叉式升降設備，在高空工作中難免會出現搖擺。那不同的升降機由于其各自的特性表明著各自高空作業的高度不同，搖擺的幅度也就大不相同。一般來說，在同等條件下，固定式的升降機相對于其他升降機而言是最穩定的，擺幅也就相對最小，其次是固定式剪叉式升降機，再就是各種移動式升降機以及車載升降機了。雖然說升降機出現搖擺的現象很正常，但是搖擺的幅度卻是有一定的限制的。
As a scissor lift lifting equipment, aerial work will inevitably be rocking. That type of lift due to its own characteristics showed significantly different levels of their aerial, swing amplitude also different. In general, under the same conditions, stationary relative to the other lift lift is the most stable, relatively minimal swing it, followed by fixed scissor lifts, then there are a variety of mobile lifts and car lifts a. Although the phenomenon of swing lifts appeared normal, but the magnitude of the swing, but there is a certain limit.

3、為了人身以及設備安全，液壓升降機和液壓升降平臺工作時載重不能超過它的額定載重,當升降升到一定高度是提升的物體質量越大晃動也越大。因此，升高的高度最好控制在升降機適合工作的高度，能8米工作就不要升到9米，否則升降機升的太高而承載量又大，很容易加大升降機的擺幅從而加大危險事故發生的幾率。其次就是作業時候強度需要注意，當遇到強度十分大的工作時候，最好加強四根支撐腿，同時最好用繩索固定作業平臺四角，加強穩定性。避免出現因為過度搖擺造成各種升降臺事故。
For when personal and equipment safety, hydraulic lifts and hydraulic lifting platform work load should not exceed its rated load, when the lift is raised to a certain height to improve the quality of the larger objects greater sway. Therefore, the increased height is best controlled at the height of the lift for the job, and can not rise to 8 m 9 m working on, and otherwise lift up too high carrying capacity and large, it is easy to increase the lift of the swing thereby increasing probability of dangerous accidents. The second is when the strength of the job need to pay attention, when faced with the strength of a very big job, it is best to strengthen the four support legs, while the best corners with ropes fixed platforms and strengthen stability. Avoid excessive swings caused because of various lift accident.
 

濟南液壓升降機：http://www.leafhouse.com.cn/